While trying to use a device or computer peripheral, you may notice that the device is unresponsive. If the device is unresponsive due to being disabled and you attempt to access it again, you will see the message “This device is disabled. (Code 22)”
In most cases, this error means that the device was manually disabled in Device Manager but you may also see a Code 22 error if Windows is forced to disable the device due to a lack of system resources.
There are so many users that have been working hard to fix Error Code 22, but ended up with failures. Fortunately, you are reading this page. Just dig further to read the solutions with the specific steps I prudentially listed, and perform them one by one until the problem is successfully solved. Good luck!
Note: If you see the Code 22 error elsewhere in Windows, chances are it is a system error code that you should not troubleshoot as a Device Manager issue.
How to Systematically Fix Error Code 22 – Manual Way
Windows Error Code 22 is relatively not a complicated problem to resolve. Unlike some of the other hardware or device driver errors that you can encounter, this error code is straight to the point and almost instantly let you know how to rectify the situation.
Devices, like printers, can be enabled or disabled by way of the Device Manager interface. If you attempt to use a device and get the 22 error, you will have to navigate to the Device Manager. Once the Device Manager is open, you need to find the device which you were trying to access. Then Scroll through the list until you locate the device that is giving you the problem, and remember the name of the device.
To fix Error Code 22, perform the following steps:
1. While in Device Manager, click “Actions”.
2. After you click Actions, double-click “Enable Device”.
3. The Enable Device Wizard will pop up.
4. Follow all of the on-screen directions from the Enable Wizard Wizard.
5. After you are done following the directions, the device should once again be available for use, and presenting you with a status of enabled.
Since the most common reason you received a Code 22 error in Device Manager is because the device has been manually disabled, try manually enabling it. Most of the time this will fix Error Code 22. Don’t worry if it doesn’t work. All that means is that the Code 22 you are seeing was caused by something a bit less common. And you can move on with the following steps:
6. Restart your PC.
7. Did you install a device or make a change in Device Manager just before the Code 22 error occurred? If so, it is highly likely that the chance you made caused the error.
Undo the chance if you can, then restart your PC again.
8. Reinstall the drivers for the device.
9. Update the drivers for the device.
10. Clear CMOS.
11. Update BIOS.
12. Move the device to a different expansion slot on the mother board, assuming of course that the piece of hardware with the Code 22 error is an expansion card of some kind.
13. Replace the hardware to fix Error Code 22. A problem with the device is incompatible with your version of Windows. You can always check the Windows HCL to be sure.
Note: If you are sure that the hardware is working properly and is properly configured, then you might want to consider a repair install of Windows. If that fails to work, try a clean install of Windows. I don’t suggest doing either before you replace the hardware, but you may have to give them a try if you are out of other choices.
If you continue to have troubles where one particular device becomes disabled without your intervention, you may need to go to the device vendor’s website and see if there is a newer version of the driver for the device. If there is, follow the manufacturer’s recommended steps to install the new driver. New drivers are developed regularly by hardware manufacturers to fix system issues, like devices becoming disable for no reason.
Fix Error Code 22 in Only A Few Minutes
Here is a recommended tool that can locate, identity and fix Error Code 22 problem. Your computer should work faster and smoother after using it.
1. Install the safe Windows repair tool by clicking the green download button on the page.
2. Run the tool, and click the Start Scan Now button to find all the existing issues on your system.
3. Hit the Fix All button to fix Error Code 22 problem and other detected issues.
You might come across kinds of system conflicts, Active X errors, and registry errors during the future use of your machine. The registry on your computer will accumulate junks and errors over time. Although it’s just a fact of your computer life, there are a lot you can do to make things better, just like how you can fix Error Code 22 problem.